BETON PROWater-repellent treatment for precast concrete
BETON PRO by NANO-BAU: NANO-BAU BETON PRO is a water-repellent impregnation for concrete products. It reduces water absorption in precast concrete and landscaping elements. Selection should account for concrete density and the finished product's absorbency.
BETON PRO by NANO-BAU: NANO-BAU BETON PRO is a water-repellent impregnation for concrete products. It reduces water absorption in precast concrete and landscaping elements. Selection should account for concrete density and the finished product's absorbency.
BETON PRO — Properties and performance
- Reduces water absorption in precast concrete and landscaping elements.
- Protection selected for the material and its natural finish.
- Defined preparation and trial procedures help assess the result.
Water-repellent treatment for precast concrete
Substrates
- concrete and precast elements within the documented scope
- slabs, edging and concrete products
- fences and garden elements
- terrace slabs, steps and facades
BETON PRO — Technical parameters
| Parameter | Value |
|---|---|
| Product type | Water-based water-repellent impregnation |
| Visual effect | Natural appearance; assess the final result by trial |
| Approximate consumption | 100–150 ml/m² |
| Approximate coverage | Approximately 6.7–10 m²/l |
| Coats / sequence | 1; optionally 2, with the second applied only wet-on-wet |
| Application method | Even spraying or manual application as directed on the label |
| Protection from water | At least 3 hours after application |
| pH | 9 (undiluted product) |
| Shelf life | 3 years from the production date |
Technical documentation
Data from the product description and technical documentation. Follow the current label for the supplied variant and confirm working conditions by a substrate trial.
Surface preparation
First test a small, inconspicuous area.
- Clean the surface thoroughly, remove cleaning residues and allow it to dry. Assess existing coatings and absorbency before applying protection.
- Carry out a compatibility trial and assess the complete result before treating a larger area.
BETON PRO — Application method
- Spray only as much as the concrete absorbs; spread excess with a brush or remove with a cloth. Any second coat must be applied wet-on-wet.
- Temperature above +5°C; at least 3 hours without rain. Wear protective gloves and goggles.
- After treatment, check the uniformity of the result and follow the conditions for subsequent use stated on the label.
Conditions and drying time
Temperature above +5°C; at least 3 hours without rain. Wear protective gloves and goggles.
Consumption, packs and calculations
Approximately 80–120 ml/m².
Confirm consumption on a representative trial area; do not assume rates from similar products.
| Pack sizes | Indicative pack coverage |
|---|---|
| 1 L | Establish by trial and from the label |
| 2 L | Establish by trial and from the label |
| 5 L | Establish by trial and from the label |
| 10 L | Establish by trial and from the label |
| 20 L | Establish by trial and from the label |
| 200 L | Establish by trial and from the label |
| 1000 L | Establish by trial and from the label |
Example for 50 m²
No universal conversion applies. Establish the quantity for the particular process and substrate.
Maintenance and limitations
Renewal intervals depend on the substrate, exposure and use; check the current documentation for the specific variant’s detailed declaration.
- Do not apply to dirty surfaces or incompatible coatings. The impregnation does not remove existing stains or replace crack repair or waterproofing. Assess protection on a clean surface and adapt renewal to service conditions.
Storage and safety
- 3 years from the production date. Store in tightly closed original packaging in a dry, ventilated place, protected from overheating. Follow the label’s temperature requirements.
Read the current label and safety data sheet before use. Wear the required personal protective equipment. Do not mix with other products.
H315, H319
Product questions
Which surfaces is this product intended for?
- concrete and precast elements within the documented scope
- slabs, edging and concrete products
What consumption should I use?
Approximately 80–120 ml/m².
Confirm consumption on a representative trial area; do not assume rates from similar products.
How should the substrate be prepared?
- Clean the surface thoroughly, remove cleaning residues and allow it to dry. Assess existing coatings and absorbency before applying protection.
- Carry out a compatibility trial and assess the complete result before treating a larger area.
How is the product applied?
- Spray only as much as the concrete absorbs; spread excess with a brush or remove with a cloth. Any second coat must be applied wet-on-wet.
- Temperature above +5°C; at least 3 hours without rain. Wear protective gloves and goggles.
- After treatment, check the uniformity of the result and follow the conditions for subsequent use stated on the label.
What conditions are needed for drying?
Temperature above +5°C; at least 3 hours without rain. Wear protective gloves and goggles.
How should durability and renewal be assessed?
Renewal intervals depend on the substrate, exposure and use; check the current documentation for the specific variant’s detailed declaration.
What are the limitations of use?
- Do not apply to dirty surfaces or incompatible coatings. The impregnation does not remove existing stains or replace crack repair or waterproofing. Assess protection on a clean surface and adapt renewal to service conditions.
How should the product be stored?
- 3 years from the production date. Store in tightly closed original packaging in a dry, ventilated place, protected from overheating. Follow the label’s temperature requirements.
Planning your project with BETON PRO
Start by identifying the material, its finish and the result you want to achieve. The product information above sets out the intended use of BETON PRO. Check these details against your own surface before deciding on the treatment. A product intended for one material should not be assumed suitable for a different substrate simply because the two look similar.
Measure the area and inspect its condition before ordering. Existing coatings, dirt, uneven absorbency and previous treatments can affect preparation and application. Use a small, representative trial area to check compatibility, appearance and actual consumption. For a large project, compare several locations rather than relying on a single unusually smooth or sheltered patch.
Keep a record of the quantity used during the trial and the area treated. Where a consumption range is provided, use it as a planning guide and confirm it under the actual site conditions. Follow the stated application sequence; do not multiply a complete-treatment consumption figure by the number of coats unless the instructions explicitly require it.
Before applying BETON PRO, read the current product label and the linked technical documentation. Keep adjacent materials protected and arrange the work around the required weather and drying conditions. Inspect the result after the specified curing or drying period and plan routine maintenance according to the product’s limitations.
Explore the NANO-BAU product catalogue to compare applications, or contact NANOBIZ.PL for help identifying the appropriate product. This page describes BETON PRO; it does not replace the instructions supplied with your particular pack.