SOLAR CLEAN FOAMCleaning solar-panel surfaces
SOLAR CLEAN FOAM by NANO-BAU: NANO-BAU SOLAR CLEAN FOAM is a cleaner for photovoltaic panels. It removes dust and routine dirt from glass surfaces in solar installations. The concentrate allows the solution to be adjusted to the cleaning method.
SOLAR CLEAN FOAM by NANO-BAU: NANO-BAU SOLAR CLEAN FOAM is a cleaner for photovoltaic panels. It removes dust and routine dirt from glass surfaces in solar installations. The concentrate allows the solution to be adjusted to the cleaning method.
SOLAR CLEAN FOAM — Properties and performance
- Removes dust and routine dirt from glass surfaces in solar installations.
- Cleaning can be carried out separately from subsequent surface protection.
- Defined preparation and trial procedures help assess the result.
Cleaning solar-panel surfaces
Substrates
- panel and collector glass approved by the manufacturer
- glass facades and greenhouses
- cleaning photovoltaic panels
- removing pollen and airborne dirt
SOLAR CLEAN FOAM — Technical parameters
Approximately 50 m²/l; actual coverage depends on concentration and soiling.
Clean a cool, lightly pre-wetted surface. Wear protective gloves and goggles. Pressure and working method must be approved by the module manufacturer.
Data from the product description and technical documentation. Follow the current label for the supplied variant and confirm working conditions by a substrate trial.
Surface preparation
First test a small, inconspicuous area.
- Remove loose dirt, protect adjacent elements and select preparation and pre-wetting methods according to this product’s instructions.
- Carry out a compatibility trial and assess the complete result before treating a larger area.
SOLAR CLEAN FOAM — Application method
- Use concentrate or dilute up to 1:10 depending on the method. Sprayer: 200 ml product + 800 ml water; leave for approximately 3 minutes without allowing it to dry, then rinse.
- Clean a cool, lightly pre-wetted surface. Wear protective gloves and goggles. Pressure and working method must be approved by the module manufacturer.
- After treatment, check the uniformity of the result and follow the conditions for subsequent use stated on the label.
Conditions and drying time
Clean a cool, lightly pre-wetted surface. Wear protective gloves and goggles. Pressure and working method must be approved by the module manufacturer.
Consumption, packs and calculations
Approximately 50 m²/l; actual coverage depends on concentration and soiling.
Confirm consumption on a representative trial area; do not assume rates from similar products.
| Pack sizes | Indicative pack coverage |
|---|---|
| 1 L | Establish by trial and from the label |
| 5 L | Establish by trial and from the label |
| 10 L | Establish by trial and from the label |
| 20 L | Establish by trial and from the label |
Example for 50 m²
No universal conversion applies. Establish the quantity for the particular process and substrate.
Maintenance and limitations
The cleaner removes existing dirt; it does not itself create a coating lasting several years.
- First test compatibility in an inconspicuous area. Cleaning does not create a durable protective impregnation.
Storage and safety
- Check storage conditions and shelf life on each component’s label. Keep in tightly closed original packaging, out of children’s reach.
Read the current label and safety data sheet before use. Wear the required personal protective equipment. Do not mix with other products.
Product questions
Which surfaces is this product intended for?
- panel and collector glass approved by the manufacturer
- glass facades and greenhouses
What consumption should I use?
Approximately 50 m²/l; actual coverage depends on concentration and soiling.
Confirm consumption on a representative trial area; do not assume rates from similar products.
How should the substrate be prepared?
- Remove loose dirt, protect adjacent elements and select preparation and pre-wetting methods according to this product’s instructions.
- Carry out a compatibility trial and assess the complete result before treating a larger area.
How is the product applied?
- Use concentrate or dilute up to 1:10 depending on the method. Sprayer: 200 ml product + 800 ml water; leave for approximately 3 minutes without allowing it to dry, then rinse.
- Clean a cool, lightly pre-wetted surface. Wear protective gloves and goggles. Pressure and working method must be approved by the module manufacturer.
- After treatment, check the uniformity of the result and follow the conditions for subsequent use stated on the label.
What conditions are needed for drying?
Clean a cool, lightly pre-wetted surface. Wear protective gloves and goggles. Pressure and working method must be approved by the module manufacturer.
How should durability and renewal be assessed?
The cleaner removes existing dirt; it does not itself create a coating lasting several years.
What are the limitations of use?
- First test compatibility in an inconspicuous area. Cleaning does not create a durable protective impregnation.
How should the product be stored?
- Check storage conditions and shelf life on each component’s label. Keep in tightly closed original packaging, out of children’s reach.
Planning your project with SOLAR CLEAN FOAM
Start by identifying the material, its finish and the result you want to achieve. The product information above sets out the intended use of SOLAR CLEAN FOAM. Check these details against your own surface before deciding on the treatment. A product intended for one material should not be assumed suitable for a different substrate simply because the two look similar.
Measure the area and inspect its condition before ordering. Existing coatings, dirt, uneven absorbency and previous treatments can affect preparation and application. Use a small, representative trial area to check compatibility, appearance and actual consumption. For a large project, compare several locations rather than relying on a single unusually smooth or sheltered patch.
Keep a record of the quantity used during the trial and the area treated. Where a consumption range is provided, use it as a planning guide and confirm it under the actual site conditions. Follow the stated application sequence; do not multiply a complete-treatment consumption figure by the number of coats unless the instructions explicitly require it.
Before applying SOLAR CLEAN FOAM, read the current product label and the linked technical documentation. Keep adjacent materials protected and arrange the work around the required weather and drying conditions. Inspect the result after the specified curing or drying period and plan routine maintenance according to the product’s limitations.
Explore the NANO-BAU product catalogue to compare applications, or contact NANOBIZ.PL for help identifying the appropriate product. This page describes SOLAR CLEAN FOAM; it does not replace the instructions supplied with your particular pack.