FASADA PROTECT H100Water-repellent treatment for renders and facades
FASADA PROTECT H100 by NANO-BAU: An impregnation for facade renders that reduces water absorption in renders and selected facade coatings. The colourless protection helps retain the appearance of facades exposed to rain and airborne dirt.
FASADA PROTECT H100 by NANO-BAU: An impregnation for facade renders that reduces water absorption in renders and selected facade coatings. The colourless protection helps retain the appearance of facades exposed to rain and airborne dirt.
FASADA PROTECT H100 — Properties and performance
- Reduces water absorption in renders and selected facade coatings.
- Protection selected for the material and its natural finish.
- Defined preparation and trial procedures help assess the result.
Water-repellent treatment for renders and facades
Substrates
- acrylic, silicone and silicate renders
- mineral and cement-lime renders compatible with the label
- building facade protection
- maintenance of decorative renders
FASADA PROTECT H100 — Technical parameters
| Parameter | Value |
|---|---|
| Product type | Water-based, colourless and odourless impregnation |
| Visual effect | Natural appearance; assess the final result by trial |
| Approximate consumption | 40–60 ml/m² |
| Approximate coverage | Approximately 16.7–25 m²/l |
| Coats / sequence | 1; optionally 2, with the second applied only wet-on-wet |
| Application method | Even spraying or manual application as directed on the label |
| pH | 7 |
| Density | 1 g/cm³ |
| Shelf life | 3 years from the production date |
Technical documentation
PDF in Polish · FASADA PROTECT H100 ↗
Data from the product description and technical documentation. Follow the current label for the supplied variant and confirm working conditions by a substrate trial.
Surface preparation
First test a small, inconspicuous area.
- Clean the surface thoroughly, remove cleaning residues and allow it to dry. Assess existing coatings and absorbency before applying protection.
- Carry out a compatibility trial and assess the complete result before treating a larger area.
FASADA PROTECT H100 — Application method
- Shake; do not dilute. Apply one coat, or two wet-on-wet, to a clean, dry substrate.
- Temperature +5 to +30°C; at least 3 hours without rain.
- After treatment, check the uniformity of the result and follow the conditions for subsequent use stated on the label.
Conditions and drying time
Temperature +5 to +30°C; at least 3 hours without rain.
Consumption, packs and calculations
Approximately 40–60 ml/m², equivalent to approximately 17–25 m²/l.
Complete treatment as instructed; no additional coat multiplier.
| Pack sizes | Indicative pack coverage |
|---|---|
| 1 L | 16.67–25 m² |
| 5 L | 83.33–125 m² |
| 10 L | 166.67–250 m² |
Example for 50 m²
2–3 l
Maintenance and limitations
The declared protection period is 6 years; actual performance depends on the substrate and conditions.
- Do not apply to dirty surfaces or incompatible coatings. The impregnation does not remove existing stains or replace crack repair or waterproofing. Assess protection on a clean surface and adapt renewal to service conditions.
Storage and safety
- 3 years from the production date. Store in tightly closed original packaging in a dry, ventilated place, protected from overheating. Follow the label’s temperature requirements.
Read the current label and safety data sheet before use. Wear the required personal protective equipment. Do not mix with other products.
Product questions
Which surfaces is this product intended for?
- acrylic, silicone and silicate renders
- mineral and cement-lime renders compatible with the label
What consumption should I use?
Approximately 40–60 ml/m², equivalent to approximately 17–25 m²/l.
Complete treatment as instructed; no additional coat multiplier.
How should the substrate be prepared?
- Clean the surface thoroughly, remove cleaning residues and allow it to dry. Assess existing coatings and absorbency before applying protection.
- Carry out a compatibility trial and assess the complete result before treating a larger area.
How is the product applied?
- Shake; do not dilute. Apply one coat, or two wet-on-wet, to a clean, dry substrate.
- Temperature +5 to +30°C; at least 3 hours without rain.
- After treatment, check the uniformity of the result and follow the conditions for subsequent use stated on the label.
What conditions are needed for drying?
Temperature +5 to +30°C; at least 3 hours without rain.
How should durability and renewal be assessed?
The declared protection period is 6 years; actual performance depends on the substrate and conditions.
What are the limitations of use?
- Do not apply to dirty surfaces or incompatible coatings. The impregnation does not remove existing stains or replace crack repair or waterproofing. Assess protection on a clean surface and adapt renewal to service conditions.
How should the product be stored?
- 3 years from the production date. Store in tightly closed original packaging in a dry, ventilated place, protected from overheating. Follow the label’s temperature requirements.
Planning your project with FASADA PROTECT H100
Start by identifying the material, its finish and the result you want to achieve. The product information above sets out the intended use of FASADA PROTECT H100. Check these details against your own surface before deciding on the treatment. A product intended for one material should not be assumed suitable for a different substrate simply because the two look similar.
Measure the area and inspect its condition before ordering. Existing coatings, dirt, uneven absorbency and previous treatments can affect preparation and application. Use a small, representative trial area to check compatibility, appearance and actual consumption. For a large project, compare several locations rather than relying on a single unusually smooth or sheltered patch.
Keep a record of the quantity used during the trial and the area treated. Where a consumption range is provided, use it as a planning guide and confirm it under the actual site conditions. Follow the stated application sequence; do not multiply a complete-treatment consumption figure by the number of coats unless the instructions explicitly require it.
Before applying FASADA PROTECT H100, read the current product label and the linked technical documentation. Keep adjacent materials protected and arrange the work around the required weather and drying conditions. Inspect the result after the specified curing or drying period and plan routine maintenance according to the product’s limitations.
Explore the NANO-BAU product catalogue to compare applications, or contact NANOBIZ.PL for help identifying the appropriate product. This page describes FASADA PROTECT H100; it does not replace the instructions supplied with your particular pack.