KLINKIER WETWet-look finish on compatible clinker
KLINKIER WET by NANO-BAU: A wet-look impregnation for clinker that enhances the colour of clinker and ceramics. It combines a deliberate change in appearance with water-repellent protection.
KLINKIER WET — Product overview
KLINKIER WET by NANO-BAU: A wet-look impregnation for clinker that enhances the colour of clinker and ceramics. It combines a deliberate change in appearance with water-repellent protection.
KLINKIER WET — Properties and performance
- Enhances the colour of clinker and ceramics with a wet-look finish.
- A finish selected for the intended visual effect.
- Defined preparation and trial procedures help assess the result.
Wet-look finish on compatible clinker
Substrates
- clinker and brick within the instructions’ scope
- ceramic roof tiles and absorbent or low-absorbency ceramics following a trial
- walls and cladding
- floors, brick slips and planters
KLINKIER WET — Technical parameters
| Parameter | Value |
|---|---|
| Product type | Impregnation with polymer resin in an aliphatic carrier |
| Visual effect | Wet-look finish; enhances the existing colour |
| Approximate consumption | 50–100 ml/m² according to the label; confirm full-treatment consumption by trial |
| Approximate coverage | Approximately 10–20 m²/l at the stated rate |
| Coats / sequence | 2 coats; at least 30 minutes apart |
| Application method | Spray, brush or roller |
| Protection from water | Approximately 5 hours without contact with water |
| Shelf life | 3 years from the production date |
Technical documentation
PDF in Polish · KLINKIER WET ↗
Data from the product description and technical documentation. Follow the current label for the supplied variant and confirm working conditions by a substrate trial.
Surface preparation
First test a small, inconspicuous area.
- Clean the surface thoroughly, remove cleaning residues and allow it to dry. Assess existing coatings and absorbency before applying protection.
- Carry out a compatibility trial and assess the complete result before treating a larger area.
KLINKIER WET — Application method
- Ready to use; do not dilute. Spray or brush to saturate the material without runoff, then allow to dry.
- Clean, dry substrate; at least 4 hours without water.
- After treatment, check the uniformity of the result and follow the conditions for subsequent use stated on the label.
Conditions and drying time
Clean, dry substrate; at least 4 hours without water.
Consumption, packs and calculations
Approximately 6–10 m²/l.
Confirm consumption on a representative trial area; do not assume rates from similar products.
| Pack sizes | Indicative pack coverage |
|---|---|
| 1 L | Establish by trial and from the label |
| 5 L | Establish by trial and from the label |
Example for 50 m²
No universal conversion applies. Establish the quantity for the particular process and substrate.
Maintenance and limitations
Declared wet-look effect up to 5 years; actual durability depends on the substrate and use.
- It is not an opaque paint. Assess a trial including both coats after drying. Do not dilute with water or other substances; avoid runs. Assess protection on a clean surface and adapt renewal to service conditions.
Storage and safety
- 3 years from the production date. Store locked away in tightly closed original packaging, in a cool, well-ventilated place. Keep away from ignition sources and children. Follow the label’s temperature range.
Read the current label and safety data sheet before use. Wear the required personal protective equipment. Do not mix with other products.
H304
KLINKIER WET — Product questions
Which surfaces is this product intended for?
- clinker and brick within the instructions’ scope
- ceramic roof tiles and absorbent or low-absorbency ceramics following a trial
What consumption should I use?
Approximately 6–10 m²/l.
Confirm consumption on a representative trial area; do not assume rates from similar products.
How should the substrate be prepared?
- Clean the surface thoroughly, remove cleaning residues and allow it to dry. Assess existing coatings and absorbency before applying protection.
- Carry out a compatibility trial and assess the complete result before treating a larger area.
How is the product applied?
- Ready to use; do not dilute. Spray or brush to saturate the material without runoff, then allow to dry.
- Clean, dry substrate; at least 4 hours without water.
- After treatment, check the uniformity of the result and follow the conditions for subsequent use stated on the label.
What conditions are needed for drying?
Clean, dry substrate; at least 4 hours without water.
How should durability and renewal be assessed?
Declared wet-look effect up to 5 years; actual durability depends on the substrate and use.
What are the limitations of use?
- It is not an opaque paint. Assess a trial including both coats after drying. Do not dilute with water or other substances; avoid runs. Assess protection on a clean surface and adapt renewal to service conditions.
How should the product be stored?
- 3 years from the production date. Store locked away in tightly closed original packaging, in a cool, well-ventilated place. Keep away from ignition sources and children. Follow the label’s temperature range.
Planning your project with KLINKIER WET
Start by identifying the material, its finish and the result you want to achieve. The product information above sets out the intended use of KLINKIER WET. Check these details against your own surface before deciding on the treatment. A product intended for one material should not be assumed suitable for a different substrate simply because the two look similar.
Measure the area and inspect its condition before ordering. Existing coatings, dirt, uneven absorbency and previous treatments can affect preparation and application. Use a small, representative trial area to check compatibility, appearance and actual consumption. For a large project, compare several locations rather than relying on a single unusually smooth or sheltered patch.
Keep a record of the quantity used during the trial and the area treated. Where a consumption range is provided, use it as a planning guide and confirm it under the actual site conditions. Follow the stated application sequence; do not multiply a complete-treatment consumption figure by the number of coats unless the instructions explicitly require it.
Before applying KLINKIER WET, read the current product label and the linked technical documentation. Keep adjacent materials protected and arrange the work around the required weather and drying conditions. Inspect the result after the specified curing or drying period and plan routine maintenance according to the product’s limitations.
Explore the NANO-BAU product catalogue to compare applications, or contact NANOBIZ.PL for help identifying the appropriate product. This page describes KLINKIER WET; it does not replace the instructions supplied with your particular pack.